Plumbing 101: Tips for Bathtub Installation
Plumbing 101: Tips for Bathtub Installation
Blog Article
Are you currently hunting for information and facts about How to Install a Bathtub?
Mounting a tub isn't specifically rocket science, but it does call for solid plumbing, carpentry, and also often, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably challenging project. If the old bathtub is readily accessible, the job can relocate immediately; if you have to open up a wall to remove the old bathtub and position the new tub, the job is a lot harder. In either case, the project is within a house handyman's abilities, although you will certainly need an assistant to vacate the old bathtub and also set in the new one. Make certain you have actually certified on your own for the work as well as fit trying it. Rather than hiring a specialist to take control of a halfway-completed project, it is far better to consider employing one prior to you start. Possibilities are you may need a professional plumber to make tube connections.
This post will assist you set up a new bathtub in your bathroom if you have actually currently purchased a brand-new tub as well as don't require to alter the arrangement of your previous water supply pipelines.
Your tools and also material list must comprise the following:
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your setup, then the first thing you ought to do is detach the water system. After doing so, activate the taps to drain any water remaining in the system. The procedure of getting rid of the existing taps can be quite problematic as a result of the limited access that is usually the case.
Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. When the supply pipes have been removed, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning during this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing substance.
Before moving on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new taps to fit.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will certainly need a plastic port to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the other end provides a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will certainly need decreasing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin making certain that the washing machines are in area in between the tap and also the sink. Protect the tap in position with the producer given backnut. When the tap is safely in place, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular faucet ports. The former kind needs to be linked to the tap finishes initially, tightening only by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Mounting the Tub
Using both wooden boards under its feet, position the tub in the required setting. The wooden boards are helpful in uniformly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 little points.
The next objective is to guarantee that the bathtub is leveled all round. This can be accomplished by checking the spirit level and changing the feet on the bath tub until the spirit level checks out level.
To install taps, fit all-time low of the outermost adaptable tap port to the proper supply pipeline by making a compression sign up with; after that do the same for the other tap.
Switch on the supply of water as well as inspect all joints as well as brand-new pipework for leaks as well as tighten them if essential. Load the tub as well as additionally examine the overflow outlet as well as the normal outlet for leaks.
Lastly, take care of the bath paneling as explained in the maker's user's manual. Tiling as well as sealing around the bathtub must wait until the bathtub has been used at the very least once as this will resolve it right into its final setting.
Getting ready for the Setup
Firstly, the sustaining frame provided with the bathroom needs to be fitted (if needed) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is essential to see to it that if the tap comes with a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is also sensible to fit a sustaining plate under the taps unit to stop stress on the bathtub.
Fit the adaptable faucet connectors to the bottom of both taps using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. See to it you utilize every one of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom must currently be ready to be suited its last position.
Tiling Around the Tub
In the area where the bath fulfills the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the installation can move enough to split an inflexible seal, creating the water to permeate the wall between the bath and the tiling, leading to difficulties with wetness and also possible leakages to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your fixtures and also fittings. They are sold in tubes as well as cartridges, and also can sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with spins of drenched paper or soft rope. Bear in mind to constantly fill the bathtub with water before sealing, to enable the movement experienced when the tub is in usage. The sealer can fracture rather very early if you do not consider this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise quickly available on the market. It is a good idea to fit the tiles utilizing waterproof or water-proof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an enthusiastic reader about Installing A Bathtub, I assumed sharing that editorial was smart. Sharing is good. Helping people is fun. We cherish reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Click For More Info Report this page